Specialist
Solution
Product
Document
Picture

Water/oil repellent and stain protection
ProtectGuard® Stucco is the leading product for all-round protection for coatings based on plaster, lime or cement with or without the addition of organic binder.
Designed by the Research and Development Department of Guard Industry, ProtectGuard® Stucco is an ecological revolutionary water-borne product, non toxic, solvent-free, silicone-free which is intented to protect stucco, marmorino and marmorino lustro, etc against water and stains. ProtectGuard® Stucco allows a delay in the ageing process and facilitates maintenance.
ProtectGuard® Stucco is an impregnating product, non filmmaking whilst the substrate also remains permeable to air and water vapour. Completely colourless after application; it modifies neither the aspect nor the nature of the treated substrate. Moreover, it perfectly resists UV and does notyellow over time.
ProtectGuard® Stucco is ideal for the protection of stucco, Venetian stucco, marmorino… and all coatings based on plaster, lime or cement. It can be used inside and outside on vertical surfaces. For horizontal surfaces, we recommend the use of ProtectGuard® Wet Look Semi Gloss Finish.
  • Protects against water, oily liquids and staining.
  • Makes cleaning easier.
  • NoNon film-forming, lets the surface breathe.
  • UV-resistant, does not discolour.
  • Ready to use, easy to use.
Apply using a brush.
Clean tools and equipment immediately after use with water.
  • Apply the product to a surface that is clean, dust-free, grease-free and dry.
  • Wait until the lime is perfectly carbonated so that the pH has fallen back
  • Use neat, do not dilute.
  • Always carry out a preliminary test.
  • The treated surface should be impregnated to saturation point in two applications ‘wet-on-wet’.
  • Do not over apply, eliminate any exceeding product before drying.
  • Apply from the bottom-up.
  • Drying time: 24 hours.
  • Optimum effectiveness obtained after 7 days.
  • Physical state at 20 °C: Liquid.
  • Appearence: Uncoloured.
  • Odour: None.
  • pH: 8 ± 0.5.
  • Boiling point [°C]: 100 °C.
  • Density: 1.01 ± 0.01.
  • Solubility in water [vol/vol]: total.
  • Flash point [°C]: Not applicable.
Coverage depends on the porosity of the material. the figures below should be used only as a general guideline: 2 to 4 m2 / litre for two applications.
 2 and 5 litre.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 12 months following the production date when kept in the original unopened container.
Environment-friendly product:
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Non hazardous and non toxic.
  • Biodegradable > 70%*.
  • VOC < 52 g/l*.
  • Remove all atmospheric pollution-related dirt from all surfaces to be treated before starting the treatment.
  • For best results it is essential that ProtectGuard® Stucco is used when the temperature of the substrates is between 10°C and 30°C.
  • Do not apply during rain or in very hot weather. Air temperature between 5°C and 30°C.
  • Do not dilute or mix with any other product.
  • We recommend maintaining regularly the surface to keep its new look.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves. Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
KEEP OUT OF THE REACH OF CHILDREN
Stain resistance test
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
Website: www.guardindustrie.com     
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible
with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
 
Accessing: 99
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.732.676
Home
Search
Member
Contact
Other
  • Login
  • Register
  • Profile
  • Other