Water & oil repellent and anti-staining protecting marble, granite and low porous materials raw or soften
ProtectGuard® MG Eco is a product designed to protect low porosity substrates. It prevents penetration by water, oil, grease, weak acids (fruit juice, ketchup, etc.) as well as all types of soiling. ProtectGuard® MG Eco is a new generation water-based product that is significantly less hazardous than other products available in the market. Indeed, it is not classified as either corrosive or irritant. ProtectGuard® MG Eco is an impregnation, non film-forming product: treated materials remain permeable to air and water vapour. ProtectGuard® MG Eco is colourless and does not change the appearance or composition of the treated material. In addition, it is UV-resistant and does not discolor with age.
ProtectGuard® MG Eco can be used inside and outside on all vertical and horizontal surfaces. It is ideal for treating all low porous materials raw or soften: marble, granite, concrete, slate...
On porcelain stoneware, polished, crystallized or very low porous materials, use ProtectGuard® MG.
ProtectGuard® MG Eco is used for new and renovated constructions.
 
  • Effective for more than 10 years.
  • Protects against water, oily liquids.
  • Anti-staining and anti-soiling.
  • EU food contact compliance**.
  • Limits surface moss and lichen growth.
  • Prevents deterioration resulting from freeze-thaw cycle.
  • Non film-forming, lets the surface breathe.
  • Cost-effective, a small quantity of product is sufficient to protect a large surface.
  • UV-resistant, does not discolour.
  • Abrasion-resistant.
  • Ready to use, easy to use.
Apply using a roller, a brush, a microfiber cloth or flat mop.
Clean tools and equipment immediately after use with water.
  • Apply the product to a surface that is clean, dust-free, greasefree and dry. To remove greasy stains use Guard Cleaner® Eco Soiled Floors. For efflorescence, laitance or concrete bloom use Guard Remover® Eco Efflorescence & Cement. Surface preparation ensures good efficiency of the treatment.
  • Rinse carefully and wait until the surface is completely free from any cleaner marks before applying ProtectGuard® MG Eco.
  • Shake the product well before use.
  • Use neat, do not dilute.
  • Always carry out a preliminary test.
  • The treated surface should be impregnated in a single application.
  • The product must penetrate completely and allow to dry.
  • Do not over apply the product; remove any excess with a clean cloth by swabbing before the product dries.
  • Drying time: 1 hour.
  • The surface must be protected for 24 hours from traffic and liquids (rain, grease…).
  • Optimum effectiveness obtained after 7 days.
  • Physical state at 20°C: Liquid.
  • Appearence: Pale yellow.
  • Odour: Slight.
  • pH: 5 ± 0.5.
  • Density: 1.01 ± 0.02.
  • Solubility in water [vol/vol]: Soluble.
  • Flash point [°C]: > 100°C.
Coverage depends on the porosity of the material. The figures below should be used only as a general guideline: 8 to 20m² / litre.
750 ml and 5 litres.
  • Keep in a dry place (between 5°C and 30°C).
  • Storage: 24 months following the production date when kept in the original unopened container.
Stubborn dirt should be cleaned off with clean water or with a pH neutral cleaner.
Environment-friendly product:
  • Water-based product.
  • Petroleum solvent and silicone free.
  • Non hazardous and non toxic.
  • Biodegradable > 80%*.
  • VOC = 52 g/l*.
  • Rating for VOC emissions into idoor air: B.
  • For best results, it is essential that ProtectGuard® MG Eco is used when the temperature of the substrates is between 5°C and 30°C.
  • Do not apply on porcelain stoneware, polished, crystallized or very low porous materials. Use ProtectGuard® MG.
  • Do not apply during rain or in very hot weather. Air temperature between 5°C and 30°C.
  • Do not dilute or mix with any other product.
  • Resistance to acids on calcareous materials (non cristallized marble...) is limited. It is necessary to eliminate quickly acids on these materials.
  • Respiratory protection: Under normal conditions of use where adequate ventilation is available, no special respiratory protection equipment is needed.
  • Hand protection: Wear latex gloves.
  • Skin protection: No special protective clothing or skin protection is required under normal conditions of use.
  • Eye protection: If there is a real risk of splashing, wear protective goggles.
  • If swallowed: Do not induce vomiting. Contact a doctor or a specialist.
Water, oil and acid resistance of materials treated with ProtectGuard® MG Eco. Rating from 1 (weak) to 5 (excellent).
Chemical nature:
Water-borne fluorinated copolymer based.
GUARD INDUSTRIE (FRANCE)
Daniel Bruyat: Business Director
Phone: (+33) 65 84 46 13 73
Email: daniel.bruyat@guardindustrie.com
 
NANO PHAM GROUP (VIET NAM)
Hotline: (+84) 918 244 844
Email: global@nanophamgroup.com
Website:
 
Important: The content of this documentation is based on our experience with the product. Guard Industry guarantees the quality of its products but expresslydisclaims all liability if the user does not follow the recommendations and conditions of use of the products, especially but not exclusively in the case of faultyapplication, application by untrained personnel, use of products not compatible with Guard Industry products, or adverse weather conditions For more information, consult the safety data sheet.
Accessing: 71
  • Ho Chi Minh
  • 97 Street No. 7, An Phu- An Khanh Urban Area, An Phu Ward (District 2), Thu Duc City, Ho Chi Minh City
  • Quang Ngai
  • 370 Nguyen Tu Tan Street, Tran Phu Ward, Quang Ngai City, Quang Ngai Province
  • Danang
  • K21/H2/1 Nguyen Van Hue Street, Thanh Khe Tay Ward, Thanh Khe District, Da Nang City
  • Thua Thien Hue
  • B08 The Manor Crown, To Huu Street, Hue City, Thua Thien Hue Province
  • Quang Binh
  • 37 Tran Kinh Street, Dong Hoi City, Quang Binh Province
  • Ha Tinh
  • 64 Le Thai To Street, Ky Thinh Commune, Ky Anh District, Ha Tinh Province
  • Thai Binh
  • 36A Quang Trung Street, Tran Hung Ward, Thai Binh Province
  • Thanh Hoa
  • 597 Street 1, Quang Hung Ward, Thanh Hoa City, Thanh Hoa Province
  • Hanoi
  • 99 Nhat Chieu Street, Nhat Tan Ward, Tay Ho District, Hanoi City
  • Hotline: 0918 244 844
  • Email:global@nanophamgroup.com
Total online: 1.158.051